OLED Black Screen (True Black and Burn-In Test)

A black screen for OLED in true #000000: every pixel of the full-screen layer is red 0, green 0 and blue 0, so on an OLED panel those pixels are switched off. Behind it are 7 more full-screen check screens for an OLED test: middle grey (18 % light), grey 50 %, red, green, blue and white at a brightness you choose, and a near-black ladder from 0 to 10 % grey. Step through them with the arrow keys to look for burn-in and image retention (ghost logos, taskbars, clocks), black crush and raised blacks. The cursor hides after 2 seconds, keep-awake stops the screen locking while a check screen shows (where your browser supports it), and Esc, a tap or a double-click closes it. Nothing is uploaded, and once the page has loaded it keeps working with no internet connection. The page only shows colours: it does not fix burn-in.

100% private — everything runs in your browser. Everything runs in your browser; nothing is uploaded.

100% private — runs in your browser

Esc, a tap or a double-click closes the check screen. In full screen, arrow right and left step through the 8 screens, the keys 1 to 8 jump to one, and arrow up and down change the brightness of the red, green, blue and white screens. The cursor hides after 2 seconds without moving.

Check screen

Screen

Runs in your browser with our own code: nothing is uploaded or saved. Once the page has loaded it keeps working with no internet connection.

How to run an OLED burn-in test

  1. Dim the room, let the screen run for a few minutes and set the brightness you normally use.
  2. Leave the start screen on True black #000000 (or pick another check screen) and press Open full-screen check. The cursor hides after 2 seconds without moving.
  3. Press arrow right to step through the 8 screens. On each one, look for the marks listed in the table below.
  4. Press Esc, tap or double-click to close. If you see marks, follow the steps under What to do next.

What you can use it for

  • Check a new or second-hand OLED TV, monitor, laptop or phone for burn-in before you keep it
  • Look for a ghost of a taskbar, logo or game HUD after long sessions with the same picture
  • Tell short image retention from lasting burn-in by checking again after normal use
  • Check near-black detail: black crush, raised blacks and blotches near black
  • Check the screen again after your device has run its own panel refresh
  • Show a true black screen on an OLED, with the cursor hidden

The 8 check screens

KeyScreenColourWhat to look for
1True black #000000#000000Pixels that stay lit or glow, and any faint shape. On an OLED every pixel should be off.
2Middle grey (18 % light)#767676Ghost logos, taskbars, clocks or bars that are darker or tinted. Mid greys show uneven wear well.
3Grey 50 % signal#808080Darker patches, bands or a tinted edge on an even grey.
4Red (retention check)#FF0000 at 100 %Areas that look darker, more orange or more pink than the rest.
5Green (retention check)#00FF00 at 100 %Areas that look darker or more yellow than the rest.
6Blue (retention check)#0000FF at 100 %Areas that look darker or more purple than the rest.
7White (retention check)#FFFFFF at 100 %Yellow, pink or green tinted shapes, and darker outlines of things that were on screen for a long time.
8Near-black ladder 0–10 %#000000 to #1A1A1AEach step should look a little lighter than the one before it: steps that merge into black (black crush), a 0 % step that looks grey (raised blacks), or flicker and blotches near black.

Brightness (from 10 to 100 % in steps of 5) applies to the red, green, blue and white screens; true black, the two greys and the ladder stay fixed so you can compare them between checks.

Near-black ladder values

StepGrey value (0 to 255)Colour code
0 %0#000000
1 %3#030303
2 %5#050505
3 %8#080808
4 %10#0A0A0A
5 %13#0D0D0D
6 %15#0F0F0F
7 %18#121212
8 %20#141414
9 %23#171717
10 %26#1A1A1A

Each step is that share of the full signal, the same in red, green and blue. The steps run left to right on a wide screen and top to bottom on a tall one.

What to look for

  • Shapes that stay in the same place on the grey and colour screens: a logo, a taskbar or dock, a clock, a game HUD, a news ticker or subtitles.
  • Darker, tinted or blotchy areas on an even screen, especially near the edges and corners.
  • Pixels that stay lit on true black.
  • How many ladder steps you can tell apart from black.
  • Move your head a little: a mark that stays in place is on the screen, not a reflection.
  • Show normal moving pictures for a while, then check again: a mark that fades was image retention; one that stays may be burn-in.

What to do next

  • A faint mark that fades: nothing to do. Showing varied pictures usually clears image retention.
  • A mark that stays: run your device’s own panel refresh (pixel refresher, panel refresh or panel care) as its manual describes, then check again here.
  • To lower the risk of new marks: hide static bars where you can, use a screen saver or let the screen turn off when idle, and avoid very high brightness for static pictures.
  • If the mark is still there, contact the maker or seller; burn-in cover differs between warranties.
  • This page does not fix burn-in or change any setting on your device.

Keys and taps in full screen

Do thisWhat happens
EscCloses the check screen
Tap, click or double-clickCloses the check screen
Arrow right or left, or spaceNext or previous check screen (8 in a loop)
1 to 8Jumps to that check screen (numbers as in the table above)
Arrow up or downBrightness of the red, green, blue and white screens up or down by 5 %
Move the mouseShows the cursor again; it hides after 2 seconds without moving

Which tool to use

You wantUse
Burn-in, image retention and near-black checks on an OLEDOLED Black Screen (this page)
A plain black screen with a timer, a dim screen or a red night screenBlack Screen
Solid colours in a cycle to find dead or stuck pixelsDead Pixel Test
The pixel size of a screenScreen Sizes

For a black screen with a timer, or a dim or red screen at night, use the Black Screen; to cycle solid colours and look for dead or stuck pixels, the Dead Pixel Test; for the pixel size of a screen, Screen Sizes.

More free tools

More screen tools?

Screen and colour tools that run privately in your browser, with no sign-up.

See all free tools →

Frequently asked questions

Is the OLED black screen really true black?

Yes. The True black screen is #000000: every pixel of the full-screen layer is red 0, green 0, blue 0, and no text, button or hint is drawn on it. Our tests take a picture of the open screen and check every pixel. On an OLED panel a pixel showing #000000 is switched off and gives off no light.

How do I do an OLED burn-in test?

Dim the room, let the screen run for a few minutes, then open the check screens and step through them with the arrow keys. Burn-in and image retention are easiest to see on the middle grey, grey 50 % and the solid colour screens, as shapes that stay in the same place: a logo, a taskbar, a clock or a game HUD.

What is the difference between image retention and burn-in?

Image retention is a faint ghost of something that was on screen for a long time, which fades after a while of showing other pictures. Burn-in is lasting: some pixels have aged more than others, so the mark stays. If a mark fades after normal use, it was image retention.

Can this page fix burn-in?

No. A web page can only show colours, and no colour pattern undoes uneven pixel wear. Use your device’s own panel refresh (often called pixel refresher, panel refresh or panel care) as its manual describes, and contact the maker or seller if marks stay.

What is a pixel refresher?

A maintenance routine built into many OLED TVs and monitors. It measures and evens out how much the pixels have aged. Some devices run it by themselves in standby, so leave them plugged in; others have a menu item to start it by hand. Your device’s manual says where it is and how often to use it.

Why middle grey 18 % and grey 50 %?

Even mid greys make darker or tinted patches easy to see. Middle grey is 18 % of full light, which is #767676 in screen colour codes. Grey 50 % is half of the full signal, #808080, and looks a little lighter.

What does the near-black ladder show?

Eleven steps from 0 % (true black) to 10 % grey. If the steps at 1, 2 or 3 % look the same as black, dark detail is being crushed. If the 0 % step looks grey, blacks are raised. Blotches or flicker in the dark steps show uneven near-black output.

Does a black screen save battery on an OLED?

On an OLED panel a pixel showing #000000 is switched off and gives off no light. On an LCD the backlight stays on whatever colour is shown, so black can look dark grey in a dark room. The page does not measure power or battery use.

How do I exit the check screen?

Press Esc, tap the screen or click it, or double-click. On a phone or tablet that does not allow web pages to go full screen, the check screen fills the browser window instead, and the page tells you.

Does it work offline?

Yes, once the page has loaded. Everything it needs is already in the page, so every check screen and setting keeps working without a connection. Our tests switch the browser offline and run every step.

Is it free, and is anything uploaded?

Yes, it is free, with no sign-up and no usage limit. Nothing is uploaded: the colours are set by JavaScript in your browser, nothing is sent anywhere and nothing is saved when you close the page.